Two port rf networkscircuit representation, rftransistor amplifier design and matching networks, microwave passive components, microwave semiconductor devices, microwave tubes and measurements of ec2403 following anna univ. Circuit analysis ec8251 anna university lecture notes. Recall, true open circuits are difficult to create at rf mw. Firstly, let us consider the oneport circuit with which we have already become familiar. Associated with each port is the notion of a reference plane at which the wave amplitude and phase is defined. Basic circuit elements such as resistors, capacitors, inductors and independent sources. Thus, sparameters are an extremely accurate representation of the.
Model of the terminated two port circuit a two port circuit is typically driven at port 1 and loaded at port 2, which can be modeled as. Introduction to network analyzer measurements national instruments. Provides a means of designinganalyzing networks with overall system performance in mind. Circuit theorytwo port networks wikibooks, open books. Two terminals constitute a port if the currents applied to them satisfy the essential requirement known as the port condition. Sparameters are mostly used for networks operating at radio frequency rf and.
Threeterminal devices such as transistors can be configured into twoport networks. To measure devices with more ports the architecture needs to be extended. Ec2403 rf and microwave engineering 1 it is a 2 port device it is a 3 port device 2 it cannot be used as circulator it is used as isolator by terminating one port 3 if input is given in port 1,output is obtained at port 2 and vice versa each terminal is connected only to the next terminal. We can represent this as a two port circuit, which has an input port and an output port. Acoe312 circuit and packet switching 2 key points circuit switching circuit switching is used in public telephone networks and is the basis for private networks built on leasedlines. What is the difference between network and circuit. Until then, network analysis had been limited to manual measurements of standing waves in a. We can represent this as a twoport circuit, which has an input port and an output port. One port network representation is shown in the following figure. Learn vocabulary, terms, and more with flashcards, games, and other study tools. A twoport network is an electrical network circuit or device with two pairs of terminals to connect to external circuits.
A twoport network is an electrical network with two separate ports for input and output. Dec 06, 2016 an electrical network is an interconnection of various electrical elements like resistors, inductors, capacitors, batteries etc and electrical networks can either be closed or open pathand a network is a. We will see that a twoport circuit can be modeled by. The relationships can be determined experimentally. A port is an access to the network and consists of a pair of terminals. An amplifier is a device that takes an input and gives a proportional but not necessarily larger output. The term scattering is more common to optical engineering than rf. A one port circuit is a circuit for which power can enter or leave through a single wave guide or transmission line. We also observe that power can be reflected by a port, so the input power to a single port can partition between all the ports of the network to form outgoing waves. Thus, a twoport network has two terminal pairs acting as access points.
Networking primer important lan and wan highspeed technologies in todays business environment, among the most widely discussed networking topics are the technologies that make networks faster, such as fast ethernet and gigabit ethernet, as well as the technologies that connect geographically distant networks, such as frame relay, atm, and sonet. Single and multiport networks single and multiport network representations consist of inputoutput relationships without knowing the internal network. Resistors, inductors and capacitors are the examples of one port network because each one has two terminals. The concept of describing rf circuits in terms of waves is discussed and the. Circuit theorytwo port networks wikibooks, open books for. They form the basis of nearly all more complex circuits. Microwaves are electromagnetic waves with wavelengths ranging from 1 mm. The current entering one terminal of a pair leaves the other terminal in the pair. A pair of terminals through which a current may enter or leave a network is known as a port. Example problems involving both passive and active circuits will be solved using matlab. Rf transistor amplifier design and matching networks part a 1 what are the considerations in selecting a matching network. Scattering parameters or sparameters describe the electrical behavior of linear electrical. Study 35 terms chapter 16 mis 500 flashcards quizlet.
Firstly, let us consider the one port circuit with which we have already become familiar. Rf and microwave engineering ec2403 notes annauniversity. This involves setting the current on all the other ports equal to 0. Define s matrix scattering matrix is a squre matrix which gives all the combination of power relationships between the various input and output port of a microwave junction. It is the ratio of the voltage at port 2 to the current at port 1 when port 2 is open. Two terminal devices or elements such as resistors, capacitors, and inductors result in one port networks. An isolator is a two port nonreciprocal device which produces a minimum attenuation to wave in one direction and very high attenuation in the opposite direction.
1533 1186 732 321 1188 1289 1580 776 1052 171 862 1024 988 568 184 942 1297 163 1516 71 63 1304 447 1017 979 467 763 1168 692 549 1293 1474 1342 1109 432 1366 819 878 1296